AVS 67 Session AP-Invited On Demand: Atomic Scale Processing Invited On Demand Session

Gas cluster ion beams (GCIBs) are clusters of several thousands of gaseous atoms or molecules. Since thousands of low-energy (several eV) molecules bombard the same position simultaneously, bombarded area experiences transient high-temperature and high-pressure conditions. These phenomena enhance surface reactions, and also enhances desorption of etching products.

We have been studying atomic layer etching using low-energy GCIB to enhance the surface reactions between adsorbed molecules and target atoms.

In this study, we report the surface reactions between metals (such as Ni) and diketone molecules induced by Ar or O2-GCIB irradiation. From the in-situ XPS studies, the nickel oxide layer with acac or hfac adsorption are selectively removed by 5 keV Ar-GCIB irradiation. After removal of the nickel oxide, metallic nickel surface appeared, and etching stopped. From the etching depth measurement after multi-cycle ALE of Ni films, it also showed that both oxidation of nickel and adsorption of acac were necessary for Ni ALE with GCIB. In this report, preliminary results of etching of MoS2 using GCIB will be also reported.

Current and future thin film processes require quantitative characterization from the early phases of film growth to complex film stacks with a total thickness of only a few nm. While many surface analytical techniques are challenged by this requirement, Low Energy Ion Scattering (LEIS) analysis is ideally suited for ultra-thin film and sub-monolayer characterization. The key property is its single atomic layer information depth.

By scattering noble gas ions from the surface of the sample, LEIS determines the elemental composition of the surface of the outermost atomic layer. Nucleation processes and layer closure are investigated, but also diffusion from the bulk towards the surface can be studied with in-situ sample heating and continuous monitoring the surface composition.

In addition to the surface composition, also the distribution of elements over the first few nm of the sample is contained in the spectra. The so-called "in-depth information" is acquired in a virtually non-destructive way, avoiding sputtering and therefore the long measurement times and artefacts associated with it. For sufficiently thin films, the depth resolution is only a few Angstroms. This allows to study the development of the film thickness while also monitoring the film closure to determine the growth mode.

In some cases, low energy noble gas sputtering can is applied to extend the depth range beyond a few nm or to handle complex materials where "in-depth" and surface information cannot be deconvoluted.

In this contribution, we will highlight a number of examples from quite different materials and film systems. These will be used to illustrate how LEIS is applied in practical way. We will show how LEIS contributes unique information for modern ultra-thin film characterization.

ALD of metals can suffer from long nucleation delays leading to unwanted growth outside the patterned regions.We present an approach that first deposits a metal oxide selectively and reduces this metal oxide to the metal.This metal then serves as the nucleation site for ALD of Pd using a precursor chemistry that requires activation of molecular hydrogen.In the event non-selective nucleation occurs on passivated regions, we describe a low temperature ALE route to etch clusters/islands on the passivated regions faster than the desired film.This low temperature route exploits the general findings that metal oxides can be etched by a variety of vapor phase etchants – the issue is controlled oxidation while minimizing damage to adjacent surfaces.We present a low temperature route that involves VUV activation of O2 to produce atomic oxygen and ozone, with atomic oxygen being the dominant species that oxidizes the near surface region of Pd.Oxidation extents differ between continuous films and discontinuous films enabling the removal of metal islands without significantly etching the film.

This talk will discuss patterning an oxide substrate using UV-crosslinked 40-nm polystyrene (PS) films; the uncrosslinked PS is dissolved with toluene to expose the oxide surface. The ALD of NiO is highly selective on the exposed oxide surface using bis(N,N’-di-tert-butylacetamidinato)nickel(II) and H2O as coreactants. Ni and partially reduced NiO(1-x) are generated using molecular hydrogen and/or atomic hydrogen to present a surface that dissociates H2 and enables Pd ALD with Pd(hfac)2 and H2 to proceed with little to no nucleation delay. Finally, the talk will discuss vacuum ultraviolet (115 nm < λ < 400 nm) enhanced atomic layer etching (ALE) of thin (~2 and 20 nm) Pd films at 100 °C using formic acid as the etchant. Density functional theory is used to study the adsorption of oxidants (O and O3) and nudged elastic band calculations describe O diffusion into the films to understand the kinetic limitations of the oxidation step. Low-temperature Pd oxidation at 100 °C is achieved by exposure to vacuum ultraviolet (VUV) light (λ<160 nm) in the presence of O2. The islands are completely oxidized while Pd oxidation of a film is limited to approximately one atomic layer. Any PdO that forms is etched by exposure to formic acid.

Selective deposition by ALD can be obtained using: inherent selectivity of the process^1-2, surface activation³, surface deactivation ^4-5, and ABC typesuper-cycles ⁶. The strategy developed in our laboratory is based on super-cycles with alternate deposition and etching steps^7-10 in a unique ALD tool.

Up to now, we have developed ASD processes with many different types of etching steps, such as high-pressure plasma etching (radicals only), Reactive Ion etching, Atomic layer etching or sputtering (physical) etching steps. For this purpose, two different PEALD tools are used: either a CCP capacitive discharge tool from Kobus (now Plasma-Therm) with a grounded substrate holder, or an ICP PEALD tool from Oxford (Flexal) with an additional RF biasing of the substrate.

Plasmas from the PEALD tool can also be developed to the benefit for ASD processes. For instance, an appropriate plasma chemistry can modify the nucleation delay. Moreover, thanks to substrate biasing, one can also take advantage of energetic ions from the plasma to locally modify the nucleation delay as well as the materials GPC or density. This latest route combined with a post-deposition etching process is a fast and easy to develop process for topographically selective deposition (deposition in one space direction only).

This presentation will outline and provide several examples of all these different scenarios that we have developed recently in our group, as well as state of the art ASD solutions from other groups using etching steps or ions in PEALD processes.

¹K. J. Hughes and J.R. Engstrom, J. Vac. Sci. Technol. A 30, 01A102 (2012)

²S. E. Atanasov et al, J. Vac. Sci. Technol. A 34, 01A148 (2016)

³A.J. M. Mackus et al, Chem. Mater. 24, 1752 (2012)

⁴M. Fang and J.C. Ho, ACS Nano 9, 8651 (2015)

⁵E. Farm et al, Sci. Tech. 27, 074004 (2012)

⁶A. Mameli et al, ACS Nano 11, 9303 (2017)

⁷R. Vallat et al, J. Vac. Sci. Technol. A 35, 01B104 (2016)

⁸R. Vallat et al, J. Vac. Sci. Technol. A 37, 020918 (2019)

⁹A. Chaker et al, Appl. Phys. Lett. 114, 043101 (2019)

¹⁰C. Vallée et al, J. Vac. Sci. Technol. A 38, 033007 (2020)

In this presentation we discuss the state-of-the-art status of thermal atomic layer etching of various materials such as metals, metal oxides, metal nitrides, semiconductors and their oxides.We outline the basic chemical and thermodynamic reaction principles and identify materials relevant to the semiconductor industry that lend themselves for isotropic atomic layer etching.

Furthermore, application examples of this new etch technology are illustrated on device structures and its benefits as well as challenges are examined.We give an example of the technical challenges related to high aspect-ratio atomic layer etching including an overview on how to mitigate it in modern 3D NAND test structures.

Finally, we provide an outlook of the role thermal ALE can play in the manufacturing of advanced semiconductor devices.

As device feature sizes move beyond sub-7 nm technology node, atomic scale processing techniques such as atomic layer deposition (ALD) and atomic layer etching (ALE) are being adopted to gain control over key processing parameters.These techniques are commonly combined with thin polymer barrier layers such as self-assembled monolayers (SAM) that are selectively located to achieve area selective deposition or etching. Atomic scale thicknesses, nanoscale lateral dimensions, and the combination of multiple materials consisting of organic and inorganic compounds, metals, and 1D/2D materials demand new metrology and characterization techniques to be developed to adequately asses and monitor these advanced processing techniques.Photo-induced Force Microscopy (PiFM) [1] combines infrared (IR) absorption spectroscopy and atomic force microscopy (AFM) to achieve nanoscale chemical analysis via localized IR absorption spectrum and mapping of heterogeneous materials on the surface of a sample (with sub-10 nm spatial resolution). The spectroscopic capability is useful for ascertaining the quality of the molecular species while the mapping capability is useful for investigating chemical pre-patterns as well as selectively deposited materials in area-selective processes like block copolymer directed self-assembly, sequential infiltration synthesis, and a variety of area-selective deposition techniques. PiFM applications on various atomic scale processes will be presented.

[1] D. Nowak et al., Sci. Adv. 2, e150157 (2016).