ICMCTF2013 Friday Morning
Sessions | Time Periods | Topics | Schedule Overview
Hover over a paper or session to view details.
Click a Session in the first column to view session papers.
| Session | Friday, May 3, 2013 | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 8:00 AM | 9:00 AM | 10:00 AM | 11:00 AM | ||||||||
| E3-2+ |
Formation and Characterization of Reconstructive Coatings
|
Plasma Electrolytic Oxidation for Surface Treatment of Engine Cylinder Bores
|
Understanding Wear of Diamond-like Carbon Coatings for use in High-pressure Diesel Injection Engines
|
Characterization and Tribological Investigations of Arc Evaporated Mo-based Coatings
|
Development of New Oxidation Resistant Coating for Dry Hobbing
|
Third Body Behavior During Dry Sliding of Al-Al2O3 Composite Coatings: in situ Tribometry and Microanalysis
|
|||||
| F6-1 |
Prototyping Solid-Oxide Fuel Cells with Pulsed Laser Deposition
|
High Performance Nano-Coatings for Ferritic Stainless Steel Strips used as Solid Oxide Fuel Cell Interconnects
|
Strontium Diffusion in Magnetron Sputtered Gadolinia-doped Ceria Thin Film Barrier Coatings for Solid Oxide Fuel Cells
|
High Performance Duplex Coatings for PEMFC Metallic Bipolar Plates by CFUBMSIP and HIPIMS Technology
|
Industrial, Low Cost Ceramic MaxPhase™ Protective Coatings for Stainless Steel Bipolar Plates
|
Pre-coated Steel Stripes for PEMFC and SOFC Interconnects
|
R.F. Magnetron Sputtered Li-Mn-O Thin Films
|
The Effect of Reactive Element Coatings on the Oxidation Properties of Ferritic Steels for Solid Oxide Fuel Cell Interconnect Applications
|
|||
| G5-2 |
Surface Modification for Metal using a Newly Developed Atmospheric Controlled Induction-heating Fine Particle Peening (AIH-FPP) System
|
Number of Passes and Thickness Effect on Mechanical Characteristics of Cold Spray Coating
|
Effects of Intermediate Surface Treatments on Corrosion Resistance of Cathodic Arc PVD Hard Coatings
|
Microstructure and Dielectric Nature of Plasma Sprayed Ultra Purity Aluminum Oxide Coatings
|
The Fracture Toughness of Boride Coating Improved by a Diffusion Annealing Process
|
||||||
| TS1-1 |
Direct Thermal Conductivity Measurement of Nanostructured Coatings Using a Modified Photoacoustic Technique
|
Thermo-Mechanical Modeling of Carbon Nanotube Arrays for Thermal Interface Applications
|
Heat Transfer in Encased Graphene
|
Limited Thermal Conductance of Metal-carbon Interfaces
|
Thermoreflectance Microscopy of Thin Films
|
Hydrogen Absorption and Desorption Properties of Pd/Mg/Pd Tri-layers Prepared by Magnetron Sputtering
|
Interface Engineering for Optimized Thermal Transport in Copper/Diamond System
|
Synthesizing MnO2/Graphene Composites by a Hydrothermal Method for use to Enhance the Performance of Supercapacitor
|
|||
| TS2-2 |
Correlation Between the Rockwell Indentation Test and the Progressive Load Scratch Test for Assessment of Coating Adhesion
|
How to Make Tribological Tests Physical
|
Depth Profiling >40-µm Anodized Coatings Using Glow Discharge Optical Emission Spectroscopy
|
Mechanical Properties of Nanocrystalline Coatings Revealed by Bending Tests on Fabrication-Unaffected Micro-Cantilevers
|
Cyclic and Monotonic Mechanical Properties of Micro Samples Acquired with Custom Built Setups Working up to 1000 Hz – CuAl10Ni5Fe4, 3Y-PZT
|
High Cycle Fatigue of Al and Cu Thin Films by a Novel High-Throughput Method
|
Structural, Morphological and Mechanical Characterization of Mo Sputtered Coatings
|
Effect of AlN Layer on the Growth and on the Structure of Reactive Sputtered TiAlN Thin Films and Multilayers
|
Structural Characterization of Amorphous GdTM2 (TM=Fe, Ni and Co) from First-principles
|
Influence of Stoichiometry and Architecture on Mechanical Properties of Cathodic Arc Deposited Ti-Al-Cr-N Coatings
|
Fabrication and Characterization of Polymethylmethacrylate (PMMA) Thin Film by Plasma Polymerization
|