AVS2006 Session TF-MoM: ALD and Applications I

Monday, November 13, 2006 8:00 AM in Room 2022

Monday Morning

Start	Invited?	Item
8:00 AM		TF-MoM-1 Spatially Controlled Nano-Scale Doping of Er³⁺ in Y₂O₃ by Atomic Layer Deposition J. Hoang, T.T. Van, M. Sawkar Mathur (University of California, Los Angeles); J. Bargar (Stanford Synchrotron Radiation Laboratory); B. Hoex, W.M.M. Kessels, M.C.M. Van De Sanden (Eindhoven University of Technology, The Netherlands); R. Ostroumov, K. Wang, J.P. Chang (University of California, Los Angeles) We report in this work the utilization of radical enhanced atomic layer deposition (RE-ALD) to synthesize ultra thin films with controlled dopant incorporation. Er-doped Y₂O₃ is a potential waveguide core material for compact optical amplifiers because Y₂O₃ allows for incorporating of a higher concentration of Er and enables a compact geometry and a larger signal admittance angle. Extended X-ray Absorption Fine Structure (EXAFS) analysis showed that Er was in the optically active trivalent state in all samples, confirmed by their X-ray absorption near-edge spectroscopy. Modeling of the EXAFS data revealed that Er³⁺ is coordinated with 6 O at 0.224 and 0.232 nm. The critical inter-ionic distance between two Er³⁺ was determined to be 0.4 nm, thus setting an upper limit on the Er³⁺ concentration in Y₂O₃ at about three orders of magnitude higher than the Er³⁺ solubility limit in the conventional SiO₂ host. X-ray diffraction (XRD) and selected-area electron diffraction patterns revealed a preferential film growth in the [111] direction, showing a lattice contraction with increasing Er doping concentration, likely due to Er³⁺ of a smaller ionic radius replacing the slightly larger Y³⁺. The optical properties of Er³⁺ ions incorporated in Y₂O₃ were investigated by using cavity ring-down spectroscopy (CRDS), and the peak absorption cross section of Er³⁺ in Y₂O₃ at 1.53-µm was estimated to be ~2.0x10^-20 cm², about two times of that for Er³⁺ in SiO₂. This is consistent with our previously reported larger effective absorption cross session of Er³⁺ based on the photoluminescence yield as a function of the pump power. An important implication of this higher absorption cross section is that the population inversion can be achieved at a lower pump power and hence higher pumping efficiency.
8:20 AM		TF-MoM-2 MnO₂ and MgO Atomic Layer Deposition Using Bis(Ethylcyclopentadienyl) Precursors and H₂O B.B. Burton, F.H. Fabreguette, D.N. Goldstein, S.M. George (University of Colorado at Boulder) The atomic layer deposition (ALD) of manganese oxide (MnO₂) and magnesium oxide (MgO) was studied using Fourier transform infrared (FTIR) spectroscopy and quartz crystal microbalance (QCM) measurements. MnO₂ ALD was performed at temperatures between 100-300°C using sequential exposures of Mn(CpEt)₂ [bis(ethylcyclopentadienyl)manganese] and H₂O. MgO ALD was performed at temperatures between 125-400°C using sequential exposures of Mg(CpEt)₂ [bis(ethylcylopentadienyl)magnesium] and H₂O. The FTIR spectra were consistent with a loss of O-H vibrational features and a gain of C-H vibrational features during the M(CpEt)₂ exposure. The H₂O exposure produced a gain in O-H vibrational features and a loss of C-H vibrational features. The M-O bulk vibrational modes were also observed to grow in both cases between 500-1000 cm^-1. The QCM showed a maximum mass gain per cycle (MGPC) of 56 ng/cm²/cycle for MnO₂ at 150°C and a MGPC of 44 ng/cm²/cycle for MgO at 150°C. Both reactions were very efficient and required reactant exposures of only 2 x10⁵ L (1 L = 1 x 10^-6 Torr s). The X-ray reflectivity (XRR) measurements were consistent with growth rate of ~1.1 Å/cycle at 150°C and ~1.41 Å/cycle at 150°C for MnO₂ and MgO, respectively. Based on thicknesses measured by XRR and the MGPC obtained by QCM, the density for the MnO₂ ALD films was 4.95 g/cm³ and the density for the MgO ALD films was 3.15 g/cm³. Transmission electron microscopy (TEM) was also performed after 40 AB cycles of MnO₂ ALD and 50 cycles of MgO ALD on ZrO₂ particles. In agreement with the growth rates obtained from the XRR measurements, the film thicknesses observed by TEM were 54 Å and 85 Å for MnO₂ and MgO, respectively.
8:40 AM	Invited	TF-MoM-3 A New Fabrication Method of Nanostructural Materials by Using Selective Atomic Layer Deposition M.M. Sung (Hanyang University, South Korea) We report a new fabrication method of nanostructural materials by using selective atomic layer deposition of thin films on patterned self-assmebled monolayers and nanoporous templates. The patterned monolayers define and direct the selective deposition of thin films. This technique has been used successfully to deposit nanostructural materials on technologically important substrates including silicon and gold. Oxide nanotubes with diameter of 30 ~ 200 nm were successfully fabricated by this technique. It allows one-step processing for the fabrication of the freestanding oxide nanotubes. Sub-Ã.ngstrom wall thickness controls in oxide nanotubeâ?T structures can be achieved by this method. The nanostructural amaterials have been investigated by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), water contact angles analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM) and UV spectrometer.
9:20 AM		TF-MoM-5 Mechanism of Al₂O₃ Atomic Layer Deposition Using Trimethylaluminum and Ozone D.N. Goldstein, S.M. George (University of Colorado at Boulder) Al₂O₃ atomic layer deposition (ALD) is typically performed using trimethylaluminum (TMA) and H₂O. However, ozone can be used as the oxidant instead of H₂O. Ozone may lead to reduced Al₂O₃ leakage current for dielectric applications. Ozone may also purge faster than H₂O and lead to faster Al₂O₃ ALD. The mechanism of Al₂O₃ ALD using TMA and ozone is still under debate. To study the chemical species on the growing Al₂O₃ ALD surface, we have performed transmission FTIR vibrational spectroscopy investigations. High surface area ZrO₂ nanoparticles were utilized to obtain high surface sensitivities. The vibrational spectrum was recorded after each TMA or ozone reaction. The ozone generator produces 3.7 wt.% ozone in a 300 sccm O₂ flow in a viscous flow ALD reactor. Argon is utilized as the carrier gas to reduce reactive NO_x species. At the growth temperatures of 175 and 275°C, the FTIR results reveal that O₃ reacts with Al-CH₃ surface species produced by the TMA reaction and forms primarily formate groups and a mixture of methoxy and hydroxyl species on the surface. Production of formate groups may involve oxygen insertion into the Al-CH₃ bond to form methoxy species that are known to condense into formate groups at the reaction temperatures. The TMA then displaces the formate and methoxy groups and reforms Al-CH₃ surface species. FTIR difference spectra after TMA and O₃ reactions at 275°C are shown in the accompanying figure. These spectra are consistent with the loss and gain of formate and methoxy groups. The surface features are temperature dependent. At temperatures greater than 375°C, the FTIR vibrational spectrum reveals only formate groups on the surface.
9:40 AM		TF-MoM-6 Atomic Layer Deposition of Y₂O₃-Al₂O₃ Nanolaminate Thin Films and Compounds J.C. Rowland, M. Davidson, P.H. Holloway (University of Florida) Alternating nano-scale thin films of Y₂O₃ and Al₂O₃ were grown by atomic layer deposition (ALD) with AlCl₃, Y(thd)₃, and H₂O precursors. The surface roughness was determined by AFM versus growth parameters such as substrate temperature (250-550°C), gas sweep time, etc. Growth rates of 0.4 nm/cycle were demonstrated. The composition was analyzed by Auger electron spectroscopy (AES) and secondary ion mass spectrometry (SIMS), and shown to have low concentrations of impurities, especially Cl from the Al precursors. The microstructure and crystallinity / amorphicity were characterized using cross-sectional transmission electron microscopy (TEM), and X-ray diffraction (XRD). These data are interpreted in terms of the layer-by-layer ALD growth mode and compared to the properties of a single oxide film of Y₂O₃ or Al₂O₃. Solid state diffusion during post-growth annealing was investigated for forming various Y₂O₃-Al₂O₃ compounds such as Y₂Al₅O₁₂ (YAG), YAlO₃ (YAP), and Y₄Al₂O₉ (YAM), having cubic garnet, orthorhombic perovskite, and monoclinic structures, respectively.
10:20 AM		TF-MoM-8 Plasma Enhanced Atomic Layer Deposition of TiO₂ and HfO₂: Plasma Source Configuration and Film Properties S.M. Rossnagel (IBM T.J. Watson Research Center); J. Joo (Kunsan National University, Korea); H. Kim (POSTECH, Korea) Plasma enhanced atomic layer deposition has advantages over thermal atomic layer deposition method in deposition rate, deposition temperature window, film density and choice of precursors. The role of plasma can be summarized into two categories; selective dissociation of precursors and enhancement of nucleation site density. Four different configuration of high density plasma sources were developed and applied to deposit TiO₂ and HfO₂ on 200 mm Si wafers using TIIP(titanium isoproxide) and TEMAH(tetrakis ethyl methyl amido hafnium) as precursors. For reactants, oxygen and water plasma were used. In addition, these same materials were evaluated by thermal ALD in the same tool. Optical emission spectroscopy was used as a real time diagnostic tool. Thickness and refractive index uniformity was monitored by ellipsometry. Chemical composition was evaluated by XPS and RBS. TiO2 was rather insensitive to the configuration of plasma sources; the distance to the wafer, or the size of the plasma sources. 2% of non-uniformity in thickness and refractive index was typically obtained from 1 inch diameter inductively coupled plasma source, which means radical dominant process both in abstraction and nucleation steps. Leakage current and C-V characteristics showed good results in higher film thickness than 3.5nm of TiO₂. HfO₂/TiO₂ multilayer and Hf_xTi_(1-x)O₂ films were deposited to seek good combination for gate stacks.
10:40 AM		TF-MoM-9 Interface Properties of Hafnium Oxide Films Grown by Atomic Layer Deposition on Native, Chemical Oxide and H-Terminated Si Surfaces J.C. Hackley, L. Takacs, T. Gougousi (UMBC) A hot wall Atomic Layer Deposition flow reactor equipped with a Quartz Crystal Microbalance (QCM) has been used for the deposition of HfO₂ thin films using tetrakis-ethylmethylamino hafnium (TEMAH) and H₂O as precursors. HfO₂ films were deposited on H- terminated Si, native oxide and SC1 chemical oxide. Spectroscopic ellipsometry and QCM measurements confirm linear growth of the films with a growth rate of ~1.2Å/cycle at 250°C. The films composition and morphology was examined using XPS, FTIR, AFM and XRD. Films are nearly stoichiometric HfO₂ (O:Hf ~1.95) with bonded carbon content less than 3 at. % and the surface rms roughness is ~ 3% of the film thickness. A similar incubation period of ~15 cycles is found for all three starting surfaces and X-ray photoelectron emission spectroscopy shows no SiO₂ formation at the interface for deposition on the H-terminated Si surfaces. However, there is evidence for Hf-O-Si bonding and RTA inert anneals (2 min in Ar) at temperatures as low as 300°C destabilize the interface and lead to the formation of interfacial SiO₂. X-ray diffraction data indicate that the films start to crystallize upon anneals at 300°C. From the XPS and XRD data we conclude that initially the H termination of the surface and the as deposited amorphous HfO₂ network protect the interface from oxidation. However, once the film begins to crystallize then diffusion of moisture and impurity O₂ along the grain boundaries is enhanced resulting in the formation of interfacial SiO₂.
11:00 AM		TF-MoM-10 Atomic Layer Deposition of Aluminium Silicate Films P.J. Evans (ANSTO, Australia); P.H. Mutin (Universite Montpellier, France); G. Triani, Z. Zhang, A. Atanacio, J. Bartlett (ANSTO, Australia) The ALD of silicate films has been the subject of several recent studies.^1-3 Interest in these materials has been stimulated in part by research into suitable candidates for the high-k dielectric layer in future semiconductor devices. While the ALD of hafnium and zirconium silicates have figured prominently in work to date, other metal silicates, such as those of aluminium, have also been reported.^4,5 The present study investigates the deposition of aluminium silicate films by means of the reaction between aluminium chloride (AlCl₃), tetramethoxysilane (TMOS) and water at temperatures in the range 200 - 300 °C. An in-situ quartz crystal microbalance (QCM) was used to monitor the growth process in real time. The results of these measurements indicated that a single AlCl₃/H₂O pulse sequence followed by 3 - 5 pulse sequences of TMOS/H₂O enhanced both the growth rate and amount of Si in the film. These conditions were then used to deposit films on silicon wafers for ex-situ characterisation with ellipsometry, SIMS and XPS. It was found that films with approximately equal amounts of Al and Si could be obtained with the above precursors at 250 °C. At lower temperatures, the film growth rate decreased rapidly to the extent that negligible growth occurred at 200 °C. This finding is similar to that observed in other cases where ALD film growth has been found to depend on the effect of temperature on reaction kinetics. ¹Vainonen-Ahlgren, E.; Tois, E.; Ahlgren, T.; Khriachtchev, L.; Marles, J.; Haukka, S.; Tuominen, M.; Comp. Mater. Sci. 2003, 27, 65. ²Kukli, K.; Ritala, M.; Leskelä, M.; Sajavaara, T.; Keinonen, J.; Hegde, R.I.; Gilmer, D.C.; Tobin, P.J. J. Electrochem. Soc., 2004, 151, F98. ³Kang, S-W.; Rhee, S-W.; George, S.M. J. Vac. Sci. Technol. A 2004, 22, 2392. ⁴Brei, V.V.; Kasperskii, V.A.; Chuiko, A.A.; Russ. J. Appl. Chem. 1996, 69, 335. footnote5Lim, J.W.; Yun, S.J.; Lee, J.H.; Electrochem. Solid-State Lett. 2005, 8, F25.
11:20 AM		TF-MoM-11 Structure and Electrical Properties of BN Atomic Layer Deposition Grown in a Quasi-static Viscous Flow Reactor R.K. Grubbs (Sandia National Laboratories) Boron nitride (BN) is a desired material due to its thermal, electrical and tribological properties. The ability to deposit certain phases of BN via atomic layer deposition (ALD) could potentially solve a number of materials issues related to packaging and to MEMS systems. This talk describes the deposition, materials characterization and resulting electrical properties of ALD grown BN at a deposition temperature of 480 °C. Initial work on the ALD of BN was performed by Ferguson and George using FT infrared spectroscopy on ZrO₂ particles.¹ Their work determined that large reactant exposures were necessary to complete the ALD surface chemistry. To produce ALD films of BN, an ALD viscous flow reactor was run in a quasi-static mode to obtain the necessary exposures required to saturate the surface chemistry. NH₃ and two different boron precursors were used to make BN thin films. Both BCl₃ and B(CH₃)₃ precursors were successful at producing BN ALD. The resulting thin films were analyzed with depth profile Auger electron spectrometry and x-ray diffraction. The BN films were amorphous as grown and did not convert to a crystalline phase under rapid thermal annealing conditions. The BN ALD grew at a rate of 0.7 Å/cycle at the 480 °C reaction temperature. Electrical measurements were performed on the BN ALD thin films as a function of film thickness. The breakdown voltage, leakage current and dielectric constant were measured for each BN synthesis and compared. Although BN ALD is a time consuming process, it can provide amorphous, low dielectric constant, pinhole free films for potential electrical, and diffusion barrier applications. ¹ J.D. Ferguson, A.W. Weimer, S.M George, Thin Solid Films 413 16 (2002).
11:40 AM		TF-MoM-12 Plasma Controlled Atomic Layer Deposition for Sealing Pores in Low-k Materials Y.-B. Jiang, J.L. Cecchi (University of New Mexico); C.J. Brinker (Sandia National Laboratories) On a porous substrate, atomic layer deposition (ALD) takes place not only on the top of the substrate, but also penetrates into the internal porosity. For sealing the pores of a nanoporous low-k materials, it is important to prevent any deposition in the internal pores, which would alter the material's dielectric constant. Consequently, an approach capable of confining ALD to the top surface of the porous substrate is needed. We have developed such a method by combining ALD with plasma processing. The ALD process is carried out such that deposition reaction will not take place unless triggered by a plasma. TEOS and O2 have been used as the precursors for SiO2 ALD in a plasma-ALD reactor. Although both precursors will be incident on all exposed surfaces, including the internal pores, they are not reactive to each other unless triggered by active plasma radicals. Since the radicals in the plasma do not penetrate into the nanoporous matrix, no ALD will take place in the internal pores. Another approach we have developed is an ALD process for which adsorption can not proceed unless the surface is activated by plasma. Using TMCS (trimethyl chlorosilane) and H2O vapor as SiO2 ALD precursors, ALD proceeds via the cycle of TMCS/Ar purge/O2-plasma/H2O vapor/Ar purge. After each TMCS exposure, the sample surfaces are passivated with -CH3 groups. Upon the following exposure of an O2 plasma, -CH3 groups on the top surface are removed, leaving the surface reactive to subsequent precursor adsorptions. But the internal pores remain passivated, since plasma cannot reach them. In this manner, ALD is also confined to the top surface of the porous substrate. We present transmission electron microscope (TEM) images that establish that the SiO2 ALD thus obtained was a several-nm-thick pore-sealing layer conformally on the top of patterned nanoporous silica without filling the internal pores.